loading

Organized by cause → solution → cost, so homeowners can check it themselves.

Water Tank Waterproofing: Methods & Mistakes to Avoid

Water tank waterproofing repair

If you notice water leaking from a water tank on your rooftop or in a basement, or if the interior surface starts to lift, many facility managers think about waterproofing the tank. However, if you don't decide on a construction method or inspect the current condition before hiring a contractor, you're likely to face the same issues again in just a few years.

In this article, we'll walk you through the process step-by-step: how to diagnose when your water tank needs waterproofing, how to choose the right method, and the proper sequence for construction and finishing. We'll also touch on things you should consider alongside roof or terrace waterproofing.

First, Check the Signs That Your Water Tank Needs Waterproofing

Most water tank waterproofing projects begin after a leak has been confirmed. But by the time you see a leak, the waterproofing layer might already be deteriorating. Take a close look at these items first.

  • Check if the coating on the tank floor or walls is lifting or cracking.
  • See if there are widespread efflorescence or stains on the concrete surface.
  • Look for rust or corrosion around pipe connections and filter screens.
  • Note if there are water stains on the exterior of the tank or if the floor feels damp.

If two or more of these issues apply, you need to determine if a partial repair will suffice or if a complete re-waterproofing job is necessary. If you see structural cracks or wall deformation, structural reinforcement must happen before any waterproofing.

Compare the Features of Different Waterproofing Methods

The best waterproofing method for a water tank depends on your specific environment and water quality requirements. Here is a comparison of some of the most common approaches.

MethodKey CharacteristicsThings to Consider
Cement-based / Silicate-basedBonds well with concrete and is relatively simple to install.Requires careful management of thickness and curing; prone to cracking.
PE Sheet LiningCovers the entire interior with a sheet, separating the water from the structure.The quality of the sheet welding and the preparation of the existing surface are crucial.
Polyurea / Epoxy CoatingForms a seamless barrier, offering high leak-stopping power.Adhesion will fail if moisture remains, so thorough drying is essential.

Since every method has distinct pros and cons, don't just rely on what one contractor tells you. It’s wise to ask about various installation case studies and expected service life for each option.

What to Check During Construction and On-Site Inspections

The actual waterproof performance often comes down to the order of construction, not just the materials you use. Here’s the typical process:

  1. Drain the tank and thoroughly clean out the interior, removing any corrosion or debris.
  2. Repair any cracks or broken areas and smooth out the surface.
  3. Allow the base to dry completely. If any moisture remains, the waterproof coating won't stick.
  4. Apply the primer, then apply the waterproofing material according to the specified thickness and number of coats.
  5. After the curing process is complete, perform a leak test and fill the tank to do a final check.

Be extra careful around pipe penetrations and corners, as these are the most common spots for leaks. Make sure you inspect these areas closely while the work is underway.

When to Check Roof Waterproofing Alongside Tank Waterproofing

If your building has a rooftop water tank, you can't really treat the tank waterproofing and the roof waterproofing as separate issues. If the roof's surface waterproofing fails and rainwater seeps in, it will start damaging the underside of the tank or the surrounding walls first. By checking the condition of the surrounding roof waterproofing during the tank construction, you can save both time and money.

Also, when it comes to waterproofing, the construction conditions are just as important as the materials you choose. If the temperature is too low or rain is forecast, the coating might not cure properly, so make sure to factor the weather into your schedule.

Frequently Asked Questions

Can I Use Roof Waterproofing Silicone for Tank Waterproofing?

Silicone is mainly used as a sealant to fill small gaps. It isn't suitable for covering large, constantly wet surfaces like the inside of a water tank. It's generally best to consider it only as a supplementary material for finishing narrow gaps, like around pipe connections. Also, always verify that any product you plan to use meets water quality standards.

How Is the Cost of Roof Waterproofing Determined?

The price varies depending on the area to be waterproofed, whether the existing waterproofing needs to be removed, the specific method used, and the height and accessibility of the work site. There can be a big difference based on whether you have to strip off the old coating or if structural repairs are needed. When getting quotes, ask for a detailed breakdown of each item so you can compare what's included.

How Long Should I Monitor the Tank After Waterproofing?

Immediately after the work is done, you should perform a leak test. After that, it’s recommended that you drain the tank and check the interior about once a year. If you notice any lifting of the coating or water stains around the pipes, fixing even small issues quickly will prevent bigger problems down the road.

What Should Your Next Steps Be?

First off, you need to drain the tank and take some pictures inside to document its current condition. Having those photos, get quotes and explanations of the methods from two or three different companies. That will make your decision much easier. We'll keep compiling more detailed guidelines on waterproofing over at BangsuuiSin, so feel free to check it out whenever you need more info.